If you’ve been itching to try your hand at punch needling but need something less intimidating to start with than a WHOLE pillow, this is the project for you! creating this fun and festive pillow! Punch needle embroidery is the same concept but with much thinner thread, so you can work on more delicate lines, create embroidery-like images, or just get a lot of texture in a small space. It’s perfect for customizing a throw pillow or two for the holidays and can easily be scaled down to make your own ornaments!

In this round holiday pillow project, I used my embroidery punch needle to spell out the word “joy.” It took much less time than I imagined it would and since I punched it out on a red linen backing, I didn’t have to fill the whole front of the pillow and got to catch up on laundry instead.


1/2″ yard scooter red linen fabric
14″ wooden quilting hoop
Boye 2.2 embroidery punch needle
three skeins of 6 ply red cotton embroidery floss
poly-fil stuffing
JOY Pillow Template
straight pins
sewing machine (optional but I’ve linked to the one I’ve had for years and love)
iron/ironing board


After pre-washing and ironing your linen fabric, use your embroidery hoop as a guide for cutting out two 16″ circles. The embroidery hoop is only 12″ wide but you can measure out 4″ from the edge and eyeball a wider diameter. Or you can follow these instructions.

Place one of the two circles in your hoop, center it within your hoop, and tighten the screw at the top. Pull your linen fabric taut in opposite directions to keep it centered within your hoop.

Print out the provided and carefully trim along the edges of each word to create a stencil. Center it within your hoop and carefully trace inside of your stencil with a black sharpie. You can pin your paper to the fabric as a precaution if you wish. The sharpie needs to be visible from the back of the fabric.

Cut a 4′ length of 6 strand embroidery floss and split it into two bundles of 3 strands each. Six strands is too many for this size needle and less than 3 won’t stay put. Thread your embroidery punch needle according to manufacturer’s instructions. DON’T lose your needle threader. You’ll need it. Hehe … For this type of project, you’ll want to adjust the length of your needle so that it’s only sticking out about 1/2″ from the handle. Not all needles are adjustable but this can help your loop height be more consistent.

Also, flip your hoop over. You’ll be punching from the back so that your loops stick out the front.

Deep breath! Start just outside the sharpie line on one of your letters and leave about a 2″ tail hanging out from the needle end. Stitch forward, with the tail side of the needle where the thread is trailing out, on the back side. If the tail side of the needle is facing forward, it can pull your loops out more easily.

When you’re punching through the fabric, you want your needle to punch through until your handle almost touches the fabric. When you pull it back out, keep the needle close to the fabric and move forward just a smidge. How much is a smidge? About the width of your needle. Since we’re using linen and not monk’s cloth or something with more obvious rows, just make sure you are keeping your stitches close to each other. You’ll get the hang of it pretty quickly and you can always fill in the gaps with more rows.

Punch until you run out of floss. Then reload your next length. Trim your tail ends down as you go so they don’t get in the way.

Work your way around the outside of the sharpie so that it is covered up with loops on the other side. You’ll be moving your hoop as you work your way around the curves of each letter. You always want the needle to be facing in the right direction, so it’s best to rotate your hoop instead of rotating your needle. This is what three full outlines of the first letter looks like. If you like the outlined look, I suggest three rows but not less. This gives a nice thickness to each letter. If you want to fill them in, continue on.

This is the back of three row completions. You want to make sure your rows are as close together as possible to give it a full look on the front. If you see blank spots, just start a new length of thread and fill them in using more rows to keep things uniform. With this type of design, using only one color, it’s OK if you are moving all over the place with your stitches to fill things in. But if you were using different colors or making shorter loops, your rows would be more obvious and you’d want to keep things more uniform.

Continue punching rows from the outside in until all of your letters are filled in and fluffy!

Read Previous

Cooking From Cookbooks Tempeh Meatballs Recipe.

Read Next